This is just the beginning.

Here’s to embracing
your power.
your era.
within. 

Alt image

Unlimited personalization.
Infinite results. 

2 modes

5 intensities

all areas

One intelligent device that adapts to you — not the other way around

2 modes

Tighten

Firm, smooth, and refine skin texture for long-term visible results — 10 mins.

Energies Active:

Radio Frequency
(high strength)

650nm Laser

Sculpt

Lift and tone facial contours for an energized, radiant look for 6 mins

Energies Active:

Radio Frequency
(low strength)

Microcurrent

Red Light

designed for

all areas

from face to neck and beyond.

01.

Cleanse

Remove all makeup and thoroughly cleanse your face.

02.

Apply Skincare Glide

Apply a water-based serum or gel to your skin or the device head to ensure optimal microcurrent energy flow and smooth gliding.

Can be used over a sheet mask, though energy output may be reduced.

Reapply if dryness or resistance occurs.

Avoid oils or thick creams, as they can interfere with performance.

03.

Ritual

Turn On

Press and hold the Power / Mode button for 3 seconds 

(the device will enter standby).

Select Modes (Begin Treatment)

Short press the Power/Mode button to select the mode and start the treatment.

Adjust Intensity

Use the + / – buttons to adjust intensity (Levels 1–5, indicated by 1–5 lights).

Pressure & Speed Guidelines

Apply light to moderate pressure and glide at approximately 1–2 cm per second — enough for full contact, but without indenting the skin.

Treatment Timing & Beeps

A single beep every 2 minutes (Sculpt Mode: 6 minutes, Tighten Mode: 10 minutes).

Two beeps indicate the end of the current mode; the device will enter standby.

Turn Off

Press and hold the Power / Mode button for 3 seconds.

Glide with purpose. 
Repeat with care. 
Always lift.

Frequently asked questions.

Got more questions? Message us via the online chat.

  •  Results 

  •  Usage 

  •  Suitability 

  •  Technology 

  •  Purchase

How long does it take to see a visible difference?

Most users see an instant lifted, refreshed look after their first session. Visible results compound over 28 days of consistent use.

 

In an independent 28-day instrumental study*, participants measured:

 

- a 26% increase in skin elasticity

- a 23% reduction in crow's feet visibility

- a 40% reduction in forehead wrinkle depth

 

Some users notice visible tightening within 10 days. Results vary.

 

For best results, use theBeam 3 times per week for the first month.

 

*30 participants. Individual results may vary.

What should I check if progress feels slow?

Change this gradual is hard to see in the mirror. Four things to check.

 

1. Take photos. Front-on and side profile, same light, same time of day, every two weeks. Day 1 against Day 30 is the only honest comparison — daily mirror checks aren't.

 

2. Check your contact. All eight electrodes need full skin contact. Move slowly and let the warmth build before shifting to the next section.

 

3. Progress your intensity level. If lower intensities have felt comfortable for a few weeks, it is time to increase.

 

4. Prep the skin. Always apply a conductive gel or moisturizer before use. Energy transfers through hydration, not dry skin.

 

Missed sessions are the most common reason progress stalls. Consistency compounds — gaps reset the momentum.

 

Still concerned after eight weeks of consistent use? Email theConcierge.

Will it reduce facial fat?

No. theBeam uses 5.3MHz Radio Frequency calibrated to deliver 42°C thermal energy to the 3.5mm dermal layer — above the subcutaneous fat layer. This depth targets the dermis for visible firming results.

How often should I use theBeam?

Recommended Usage: 2–4 sessions per week, with a minimum 24-hour interval for skin rest.

 

Treatment Time: 6–16 minutes per session. 

 

'Sculpt Mode' runs for 6 minutes; 'Tighten Mode' runs for 10 minutes.

 

You may use one mode only or treat the same area (e.g., lower face, full face, or neck) with both modes sequentially in a single session, depending on your treatment goals.

 

The Results:

•Instant: A lifted, refreshed look immediately after use.

•Long-term: In an independent study, users experienced visible lifting, smoothing, and firming within 4 weeks. While individual results vary, early improvements are often observed within 2 weeks.

 

The Ritual: 

Consistency is the catalyst. We recommend committing to 3+ sessions weekly to build your foundation. 

 

After 28 days, you define the pace: continue for momentum, or switch to maintenance (1–2 sessions weekly).

What skincare should I use with it?

Use any water-based skincare product, this helps conduct the energy evenly and ensures smooth glide. 

 

A few options we recommend: 

• Hyaluronic acid serum (deep hydration and conductivity) 

• A hydrating sheet mask (great for comfort and glow) 

• Water-based lotion (as long as it’s not too thick or oily) 

• Pure aloe vera gel (light and soothing) 

 

Avoid creams or oils, as they block the Microcurrent and Radio Frequency (RF). 

 

If you’re ever unsure, just check the first ingredient — if it’s water (aqua), it’s usually perfect.

Can I use it on my neck or body?

Yes. theBeam can be used on the neck, jowls, and body areas like the hands, stomach, and thighs.

 

Its flat sapphire head and eight titanium electrodes ensure full-surface contact and even energy distribution, making it suitable for both smaller areas like the face and neck and larger areas such as the hands, stomach, and thighs.

 

Body skin is generally thicker than facial skin, so visible improvements may take longer and benefit from consistent use.

 

For the neck, avoid the centre directly over the thyroid.

 

It's fine to use theBeam on the upper chest and décolletage area. Avoiding the breast tissue itself, and consult a healthcare provider before doing so — particularly if you have breast implants, are pregnant or breastfeeding, or have a current or recent history of breast cancer. 

What sensations are normal during treatment?

Gentle warmth

Yes — this is expected. Continue treatment.

 

Mild tingling or pulsing

Yes — this indicates Microcurrent energy conduction. Ensure skin is well hydrated.

 

Sharp or “zapping” sensation

No — add more skincare products and/or reduce intensity.

 

Burning sensation

No — stop immediately and contact support.

 

Treatments should feel warm and active, not painful.

How hot should the device feel during treatment?

Some users expect strong surface heat. However, theBeam is capped at 42°C for controlled dermal heating — not surface overheating. So it should feel like a warm stone facial.

 

Its effectiveness comes from RF energy heating the 3.5mm dermal layer for visible firming results, rather than aggressively heating the skin surface.

 

If the warmth feels mild, this can be normal. The sensation may be softer because:

• A thicker gel layer buffers surface sensation

• Well-hydrated skin conducts energy efficiently

• Continuous movement distributes heat evenly

• Cooler room temperatures reduce perceived warmth

• The battery level is low

 

Heat builds progressively over several minutes.

Does it hurt? Is there any "zap" or twitching?

theBeam uses a gentle 200μA Microcurrent designed for a soft, comfortable experience rather than a traditional muscle workout. 

 

While it does not cause harsh muscle contractions, you may feel a lifting sensation as the current interacts with your skin.

 

Because individual tolerance varies, we recommend starting at the lowest intensity and applying generous water-based skincare to ensure even energy distribution. 

 

Your tolerance will naturally build over time with consistent use.

Is one mode meant to treat one area, half the face, or the full face?

The time allocated for each mode refers to the total treatment time, not per side.

 

You can use that time across:

 

• The full face (moving areas at each 2-minute beep)

• Half the face

• One targeted area (e.g., jawline or nasolabial folds)

 

For example, Sculpt Mode is 6 minutes total. You might treat:

• 2 mins forehead

• 2 mins right cheek

• 2 mins left cheek

 

Or dedicate the full 6 minutes to one focused area.

 

The choice depends on your treatment goal.

Can I use two modes on the same area in one session?

Yes. You can use both modes on the same area in a single session. 

 

We recommend:

• Sculpt first (radiance and lift)

• Then Tighten (visible firming)

 

Just keep your total session under 30 minutes and allow at least 24 hours between Tighten sessions.

How should I take care theBeam after use?

After Using: Turn off the device. Rinse it gently and quickly, then dry with a soft cloth. You can also wipe off any skincare products left on the device. Avoid using abrasive materials or harsh chemicals, as they can damage the device.

 

Storing: Allow the device to dry completely before storing it in a cool, dry place away from sunlight.

Can I use theBeam with an LED mask or panel?

Yes. They work well together.

 

theBeam has a 650nm laser diode and 630nm red light built in — but those are supporting energies for the RF and microcurrent, not the main event. With light, coverage is what counts. A mask or panel treats the whole face at once; theBeam's light works section by section as you move.

 

Use them on the same day or alternate. There's no conflict.

 

What theBeam replaces

A separate RF device. A separate microcurrent device. A separate laser device. All three are in one sapphire-headed chassis — so there's no reason to run them as separate steps.

 

Traveling

theBeam replaces the mask on the road. Cordless, IPX6 waterproof, magnetic charging — 10 minutes in a hotel bathroom instead of a rigid panel in your luggage.

How to charge theBeam and check the battery level?

CHARGING:

• To Charge: Set the device on the charging base when the power light is on. The battery lights on the device will blink while it charges.

• Fully Charged: The battery lights stop blinking when the battery is full.

*Note: Don’t use the device while it’s charging.

 

CHECK BATTERY LEVEL

• While Using: You can’t check the battery level.

• In Standby: Turn on the device to see the battery level. Five lights mean the battery is full; one light means it’s low.

 

LOW BATTERY WARNING

• When On or in Standby: The battery lights will keep blinking.

• When Off: Pressing the ‘Power / Mode’ button won’t turn on the device if the battery is low; the first light blinks five times and then turns off.

 

How often should I charge the device?

A full charge supports approximately 4–8 full sessions, depending on intensity and session durations. Recharge when the battery drops to 1–2 lights for optimal performance.

 

When the battery is very low, energy delivery may feel weaker. For consistent performance, use the device with at least 2–3 battery lights remaining.

Can I travel with theBeam?

Yes. The device contains a lithium battery.

 

• Carry-on luggage: Yes (recommended)

• Checked luggage: Not recommended due to airline regulations

 

Always confirm with your airline when travelling internationally.

Is it safe for dark & tattooed skin?

Yes. theBeam is designed for all skin tones. It uses controlled Radio Frequency, Microcurrent, Low-Level Laser Diode, and Red Light technologies that target deeper skin layers to support visibly firmer-looking skin, without targeting pigment.

 

Unlike high-heat or ablative lasers, theBeam operates at controlled energy levels not associated with the aggressive heat that can affect skin tone.

Is it safe for eyes & lids?

Around the eyes, yes. On the eyelid, no.

 

Work the orbital bone — the ridge above the brow and along the cheekbone under the eye. That's where crow's feet and under-eye laxity sit.

 

Never place the device on the eyelid itself, and never direct the laser or red light toward an open eye.

 

Keep eyes closed for any pass near the orbital area.

Who should not use theBeam?

While theBeam is designed with safety in mind, certain conditions make this technology unsuitable. Please review the following contraindications before beginning your ritual.

 

Do not use if you have any of the following:

• Medical Implants: Pacemakers, heart defibrillators, or any active electronic medical devices.

• Metal in the Area: Dental braces, surgical pins, or metal bone implants in the treatment area.

• Pregnancy & Age: If you are pregnant, breastfeeding, or under the age of 18.

• Health Conditions: Active acne, open wounds, fresh scars, a history of cancer, or a weakened immune system.

• Injectables: Wait at least 2 weeks after Botox or dermal fillers before treating those specific areas.

 

Sensitive Areas to Avoid:

• Prohibited Zones: Do not use on the mouth, genitals, or directly over the eyelids.

• Neck Safety: Avoid the centre of the neck (thyroid area). Only glide along the sides and jawline.

 

Smart-Safety Features

• Automatic RF Pause: theBeam includes a built-in motion sensor. The 15W Radio Frequency energy will automatically pause if the wand stops moving, preventing heat build-up and ensuring your skin remains protected.

 

Important Warnings

• Keep it Moving: Always keep the device gliding slowly across your skin. Holding the wand still in one spot can lead to unintended heat.

• Protect Your Eyes: Never look directly into the 650nm laser beam. Avoid use inside the eye socket or on the eyelids.

• Monitor the Heat: If your skin feels uncomfortably hot, stop the treatment immediately. Most users feel a warm, 'hot stone'-like sensation.

When should I NOT use theBeam?

Do not use theBeam if you:

• Are pregnant

• Have a pacemaker or implanted electronic device

• Have metal implants in the treatment area

• Have active skin infections, open wounds, or severe inflammation

• Have uncontrolled medical conditions affecting the skin

• Have recently had injectables (wait 2 weeks)

 

Avoid using over:

• The centre of the throat (thyroid area)

• Broken or irritated skin

• Areas with active eczema, psoriasis flare, or sunburn

 

If you are under medical supervision or unsure about a specific condition, consult your healthcare professional before use.

 

When in doubt, pause treatment and contact support.

Is it safe to use if I have Botox or Fillers?

Yes, theBeam is a great complement to clinical injectables. While injectables address volume and movement, theBeam helps improve the appearance of skin firmness and texture.

 

The Protocol: We recommend waiting 2 weeks after any injection to allow the product to settle before treating those areas.

 

Pro Tip: You can continue to use the device on untreated areas during this time.

What is Radiofrequency (RF)

RF is electromagnetic energy — the same category of wave that carries radio signals, tuned to a different job.

 

In skin devices, it produces controlled warmth. Not surface heat that sits on top, but energy engineered to work beyond surface warming.

 

That warmth is what drives visible firming and definition.

The specs that matter

15W & 5.3MHz. Output and frequency in the specification range of professional clinic systems — engineered for daily home use.

 

8 titanium electrodes. Energy distributed evenly across the treatment area instead of concentrated in one point.

 

42°C thermal ceiling. A hardware cap. The device cannot exceed it.

 

RF is the primary energy in theBeam. The microcurrent, the 650nm laser diode, and the 630nm red light are supporting energies — RF does the structural work.

How does theBeam compare to in-clinic RF treatments?

Solving the "Thermage® Pain"

Clinic machines like Thermage® reach the 42°C thermal threshold in seconds, which can be excruciating. theBeam reaches the same thermal destination (42°C)—we just do it progressively over minutes. You get the stimulation, but it feels like a hot stone massage rather than a medical procedure.

The "Engine" Reality

Don't be fooled by wattage. A clinic machine has a 200W engine but must be "throttled down" to avoid burning you. We utilize a 15W High-Power system to deliver the maximum safe energy the skin can absorb—achieving the same 42°C endpoint without the need for painkillers or cooling sprays.

Fractional RF vs. full-field RF — which do you want at home?

Fractional RF splits energy into micro-zones. Between those zones, skin gets nothing.

 

That's deliberate in a clinic, where a practitioner runs multiple sessions to build coverage over time. At home, it means every pass treats a fraction of the surface under the head.

 

theBeam treats all of it.

15W & 5.3MHz distributed across 8 titanium electrodes. Every millimeter under the head receives energy on every pass — no grid, no gaps, no hot spots.

 

Even coverage is why results compound instead of arriving in patches.

 

And what it costs to keep

Fractional architecture needs a consumable tip — heads that wear out and get replaced, for as long as you own the device.

 

theBeam runs one sapphire-headed chassis. A 42°C thermal ceiling capped in hardware. No recovery window, no heads to re-buy.

 

About 10 minutes, then straight into your evening.

Why we chose RF over Ultrasound for skin tightening?

The "Volume-Safe" Lift

While Ultrasound (HIFU) penetrates extremely deep, it carries a known risk of melting facial fat (volume reduction). As we age, preserving that volume is critical for a youthful look. We chose 5.3MHz RF because it improves the look of firmness while preserving your natural volume.

How does the 90-day trial work?

We want you to love your results. If theBeam isn't right for you, simply return it within 90 days for a full refund. We even cover the return shipping.

 

To qualify, the device must be returned in like-new condition:

•Fully functional with no visible damage or scratches.

•Returned with all original packaging and parts intact.

 

*Note: Returns showing excessive wear (beyond recommended use) or commercial usage may be rejected or subject to a fee.

Where are you based, and where do you ship from?

Proudly based in Australia. 

 

- Australian orders are shipped directly from our Melbourne HQ. 

- US orders are shipped from our Dallas, Texas warehouse. 

This ensures faster local delivery times and dedicated support from our Australian team.
 

Shipping Details:

- Free standard shipping in Australia & contiguous US (1–5 business days).

- Express shipping $15 (1–3 business days) — not available for 'Hawaii, Alaska & Puerto Rico'. 

- USPS Ground available for those regions (5–10 business days).

 

Orders processed within 0–2 business days.

What's the warranty?

theBeam Renew Frequency carries a 12-month limited warranty, effective from the date of delivery.

 

What's Covered

- Manufacturing defects

- Functional malfunctions not caused by user error or misuse

- If a covered issue arises within the warranty period, we repair or replace the device at no cost to you.

 

What's Not Covered

- Accidental damage, including drops and impacts

- Liquid damage beyond the IPX6 rating, including submersion

- Cosmetic wear and normal aging

- Misuse, improper handling, or unauthorized modification or repair

- Battery faults caused by charging outside our guidelines, including improper outlet voltage

 

No Consumables. Ever.

- theBeam runs on a single sapphire-headed chassis with an 8-pole titanium system.

- There are no attachment heads to replace every three months, and nothing to re-buy to keep it working.

 

Making a Claim

Email concierge@feelthebeam.com with:

- Your order number

- A description of the issue

- Photo or video of the defect

 

We may assess the product before confirming coverage.

Your 28-day renewal journey

Consistency is the catalyst. Commit to 3+ sessions weekly to build your foundation. After 28 days, you define the pace: momentum or maintenance.

Day 1

Instant Revitalization

The first 10 minutes change everything. Fluid drainage and boosted micro-circulation deliver a subtle, instant lift to your brows and jawline. 

 

You emerge from your ritual looking luminous and beautifully refreshed.

Day 28

Visible Transformation

The change becomes structural. Your skin feels denser, clearer, and more resilient.

 

This is the phase where friends tell you that you look incredible, but they can't quite pinpoint exactly what has changed.

2 Months

Sustained Definition

Now, the results are part of you. Your jawline looks reclaimed and your skin carries a youthful "bounce" that stays. 

 

You have sculpted your features while protecting the natural volume that defines your beauty. 

4 Synergies.
1 System.

The world's first system to unite 15W High-Power RF with Bio-Mimetic Microcurrent, Laser, and Red Light. 

It targets every layer of the skin simultaneously — for visibly firmer-looking skin, an energized complexion, and toned contours in a single session.

15W & 5.3MHz RF - Firm

200µA Microcurrent - Tone

650nm Laser - Renew

630nm Red Light - Calm

The skin clinic in your hands

SHOP NOW

Curated skin science, expert tutorials, and member-only privileges.

About

About Us

FAQs

Tutorials

Contact Us

Care

Warranty

Returns

Social

Instagram

Facebook

YouTube